Fardriver ND72340

48–72V, 120A battery current

This motor controller is powerful with a full 340A phase current, optimized for PMSM motors up to approx. 3 kW rated power when used in a recreational vehicle. It provides smooth, vibration-free operation thanks to sine wave drive and supports regenerative braking. Features: Sine wave, waterproof, regenerative braking, programmable, compatible with Hall sensors. NOTE programming cable sold separately. #SPECS Max power: 8640W Rated power: 1000-3000W Voltage range: 72V Phase current, max: 340A Battery current, max: 120A Regenerative braking: Yes Phase wire connector: M6 Battery cable connector: M6 Hall connectors: Yes Control modes: Forward, reverse, 3-speed, boost, brake low/high Protection: Locked rotor, overcurrent, overload, overtemperature, overvoltage, undervoltage Dimensions without cables: 179mm*117mm*61mm

Hub motor 45H16

3000W 45H 16"

Powerful and well-balanced hub motor with 3000W rated power and a full 45mm magnet height, mounted in a rugged 16-inch moped rim. Like our other motors, this one is optimized for a good balance between acceleration and speed at 72V, but here the smaller rim provides higher efficiency and thereby higher torque throughout the entire acceleration than the 26" bicycle-tire variant of the same motor. The motor has a durable construction with 142 mm dropout, which leaves room for a single speed freewheel. It is disc brake compatible. Perfect for mopeds and other electric vehicles where power and reliability are crucial. Recommended for power output up to a full 10 000W peak. Suits anyone looking for something extreme that can still be mounted on a mountain bike frame. The motor is equipped with two sets of Hall effect sensors for increased redundancy. #SPECS Rim size: rim for 16" moped/motorcycle tire Rim width: 1,6" Recommended tire width: 2.75-3" Motor rated power: 3000W Motor KV: 11,44RPM/V Disc brake compatible: Yes Rim brake compatible: Yes Phase connectors: 3x M6 ring terminals Hall connectors: 2x 6-pin DJ7061Y-2.3-21/11 male Dropout width: 142mm Axle threads: M16x1.5 Motor type: Permanent magnet synchronous motor / brushless hub motor Number of magnet pole pairs: 23 Recommended freewheel: Single speed

Hub motor 45H26

3000W 45H 26"

Powerful and well-balanced hub motor with 3000W rated power and a full 45mm magnet height, mounted in a rugged 26-inch bicycle rim. Just like our other motors, this one is carefully designed to provide an optimal combination of acceleration and top speed – without compromising on the size of the wheel. The motor has a durable construction with 142 mm dropout, which leaves room for a single speed freewheel. It is compatible with both V-brakes and disc brakes, but we strongly recommend disc brakes for the best safety. Perfect for mopeds and other electric vehicles where power and reliability are crucial. Recommended for power output up to a full 10 000W peak. The motor is equipped with two sets of Hall effect sensors for increased redundancy. #SPECS Rim size: rim for 26" bicycle tire Rim width (outer dimension): 42,5mm Recommended tire width: 2.35-3" Motor rated power: 3000W Motor KV: 9RPM/V Disc brake compatible: Yes Rim brake compatible: Yes Phase connectors: 3x M6 ring terminals Hall connectors: 2x 6-pin DJ7061Y-2.3-21/11 male Dropout width: 142mm Axle threads: M16x1.5 Motor type: Permanent magnet synchronous motor / brushless hub motor Number of magnet pole pairs: 23 Recommended freewheel: Single speed

Thumb throttle with soft spring

Hall effect sensor, universal compatibility

A quality thumb throttle with soft spring response that provides precise control and comfort. It uses a hall effect sensor and is compatible with all Gbike motors and controllers, making it a safe choice for all types of builds and upgrades. Fits common 22.2mm grips. #SPECS Type: Thumb throttle Sensor: Hall effect Compatibility: All Gbike controllers Spring: Soft Connector: JST SM 3-pin female Inner diameter: 22,2mm Cable length: 180cm

Full twist throttle with voltmeter and ignition

12–99V, with key

This full twist throttle is compatible with e-bikes and scooters at 12–99V, with automatic voltage detection up to 100V. The digital voltmeter provides a real-time display of battery status, while the built-in key and three-speed switch add extra functionality. Mounts on standard 22.2 mm handlebars. Delivered complete with left and right grips and a 180cm cable. #SPECS Color: Bronze/gold Usable voltage: 12–99V Number of wires: 5 Type: Full twist, with voltmeter and ignition key Inner diameter: 22,2 mm Features: Battery voltage display, "ignition" Cable length: 180cm

Hub motor 35H26

1500W 35H 26"

Compact and powerful hub motor for the rear wheel with 1500W nominal power, purpose-built for 72V systems. The brushless, gearless construction with 35 mm magnets provides quiet operation and high efficiency. Fits 135 mm dropouts and 6–7-speed freewheels, with support for both rim and disc brakes – disc brake is recommended for optimal control. The motor handles short-term peaks of 5–6 kW, which is enough for brisk acceleration off-road and on recreational vehicles without compromising durability. The power is calibrated for an even balance between torque and top speed at 72V, and it harmonizes particularly well with the VOTOL EM50/4 controller for smooth, precise control. #SPECS Rim size: 26" bicycle rim Rim width (outer dimension): 42.5mm Recommended tire width: 2.35-3" Motor rated power: 1500W Motor KV: 9rpm/V Disc brake compatible: Yes Rim brake compatible: Yes Phase connectors: 3x M5 ring terminals Hall connectors: 1x 6-pin DJ7061Y-2.3-21/11 male Dropout width: 135mm Axle threads: M14 Motor type: Permanent magnet synchronous motor / brushless hub motor Number of magnet pole pairs: 23 Recommended freewheel: 6S–7S

VOTOL EM-50-4

48–72 V, 80 A battery current

Programmable sine wave motor controller for electric mopeds and electric scooters, compatible with motors between 400 and 2000 watts. Provides stable and smooth operation. Max phase current 300A and voltage range 48–72V. Recommended for our 35H motors and similar. Features: Hall sensor support, reverse, low and high braking, ignition, three speed modes, sport mode, parking mode, anti-theft, regenerative braking, field weakening. NOTE programming cable sold separately. #SPECS Max power: 5760W Rated power: 3240W Voltage range: 48–72V Phase current, max: 300A Battery current, max: 80A Field weakening/flux weakening/field weakening: Yes Regenerative braking: Yes Variable regenerative braking: No Phase wire connector: M5 Battery cable connector: M5 Hall connectors: Yes Control modes: Eco/Sport, 3-speed mode Protection: Overcurrent, overvoltage, anti-theft Dimensions without cables: 181×94×50mm Mounting holes: M6

Steel torque arm

3,6 mm steel, for 12 mm axle

Strong torque arm in 3,6 mm laser-cut steel for securing the motor axle under high torque. Mounts on a 12 mm axle and fits all of our motors. It is strongly recommended to use two, one per side of the motor, for maximum safety and durability. What is a [torque arm?](/wiki/torque-arms) #SPECS Type: Torque arm Material: Steel Thickness: 3,6 mm Made for axle dimension: 14 mm Recommended use: One per side Compatibility: All Gbike motors

Fardriver ND72450

72V, 200A Battery Current

The Fardriver ND72450 is a powerful aluminum motor controller with up to 450A phase current, designed for electric vehicles with 2–4 kW motors. It offers sine wave driving for smooth operation, is waterproof, and supports regenerative braking. The Hall version is standard and is therefore suitable for motors with Hall sensors. This is our most extreme motor controller and can deliver power on par with light motorcycles. Features: Sine wave controller, waterproof, regenerative braking, programmable, compatible with Hall sensors. NOTE programming cable sold separately. #SPECS Max power: 14400W Rated power: 3000–4000W Voltage range: 72V Phase current, max: 450A Battery current, max: 200A Regenerative braking: Yes Variable regenerative braking: No Phase wire connector: M6 Battery cable connector: M6 Hall connectors: Yes Control modes: Adjustable as needed Protection: Waterproof Dimensions without cables: 189mm×121mm×60mm

Ignition lock with voltmeter

12–99 V, two keys, black

Robust ignition lock with an integrated voltmeter that clearly shows the current battery voltage between 12 and 99 V. Comes with two keys and fits most electric vehicle builds. Black housing for discreet installation in the cockpit or panel. Fits standard bike handlebars with a diameter of 22,2mm. #SPECS Type: Ignition lock with voltmeter Voltage range: 12–99 V Color: Black Number of keys: 2 Diameter: 22,2mm Cable length: 180cm Connector: JST SM 3-pin male

Programming kit for Fardriver USB

Fardriver - USB-A

1x fardriver - USB-A male 80cm 1x USB A male - USB A female 140cm

Programming dongle for Fardriver Bluetooth

Fardriver - Bluetooth

This device enables wireless adjustment of parameters via a mobile app. It is specially developed for Fardriver controllers, such as the Fardriver ND72340 and Fardriver ND72450, and is controlled entirely via an intuitive mobile app where the user can program, customize settings, and monitor performance in real time. Thanks to advanced Bluetooth technology, it offers a fast and stable connection with good range. Installation is simple and requires no extra steps; the dongle connects directly to the controller's port and is ready to use.