Programming kit for Fardriver USB
Fardriver - USB-A
Art. no: CAB-001
1x fardriver - USB-A male 80cm 1x USB A male - USB A female 140cm
From 26,90 €
Programming kit for Fardriver USB—
26,90 €
Specifications
Specifications
Delivery
Delivery
Fardriver - USB-A
Art. no: CAB-001
1x fardriver - USB-A male 80cm 1x USB A male - USB A female 140cm
Specifications
Delivery
Goes well together with
Fardriver ND72450
72V, 200A Battery Current
The Fardriver ND72450 is a powerful aluminum motor controller with up to 450A phase current, designed for electric vehicles with 2–4 kW motors. It offers sine wave driving for smooth operation, is waterproof, and supports regenerative braking. The Hall version is standard and is therefore suitable for motors with Hall sensors. This is our most extreme motor controller and can deliver power on par with light motorcycles. Features: Sine wave controller, waterproof, regenerative braking, programmable, compatible with Hall sensors. NOTE programming cable sold separately. #SPECS Max power: 14400W Rated power: 3000–4000W Voltage range: 72V Phase current, max: 450A Battery current, max: 200A Regenerative braking: Yes Variable regenerative braking: No Phase wire connector: M6 Battery cable connector: M6 Hall connectors: Yes Control modes: Adjustable as needed Protection: Waterproof Dimensions without cables: 189mm×121mm×60mm
269,00 €
Hub motor 45H16
3000W 45H 16"
Powerful and well-balanced hub motor with 3000W rated power and a full 45mm magnet height, mounted in a rugged 16-inch moped rim. Like our other motors, this one is optimized for a good balance between acceleration and speed at 72V, but here the smaller rim provides higher efficiency and thereby higher torque throughout the entire acceleration than the 26" bicycle-tire variant of the same motor. The motor has a durable construction with 142 mm dropout, which leaves room for a single speed freewheel. It is disc brake compatible. Perfect for mopeds and other electric vehicles where power and reliability are crucial. Recommended for power output up to a full 10 000W peak. Suits anyone looking for something extreme that can still be mounted on a mountain bike frame. The motor is equipped with two sets of Hall effect sensors for increased redundancy. #SPECS Rim size: rim for 16" moped/motorcycle tire Rim width: 1,6" Recommended tire width: 2.75-3" Motor rated power: 3000W Motor KV: 11,44RPM/V Disc brake compatible: Yes Rim brake compatible: Yes Phase connectors: 3x M6 ring terminals Hall connectors: 2x 6-pin DJ7061Y-2.3-21/11 male Dropout width: 142mm Axle threads: M16x1.5 Motor type: Permanent magnet synchronous motor / brushless hub motor Number of magnet pole pairs: 23 Recommended freewheel: Single speed
449,00 €
Hub motor 45H26
3000W 45H 26"
Powerful and well-balanced hub motor with 3000W rated power and a full 45mm magnet height, mounted in a rugged 26-inch bicycle rim. Just like our other motors, this one is carefully designed to provide an optimal combination of acceleration and top speed – without compromising on the size of the wheel. The motor has a durable construction with 142 mm dropout, which leaves room for a single speed freewheel. It is compatible with both V-brakes and disc brakes, but we strongly recommend disc brakes for the best safety. Perfect for mopeds and other electric vehicles where power and reliability are crucial. Recommended for power output up to a full 10 000W peak. The motor is equipped with two sets of Hall effect sensors for increased redundancy. #SPECS Rim size: rim for 26" bicycle tire Rim width (outer dimension): 42,5mm Recommended tire width: 2.35-3" Motor rated power: 3000W Motor KV: 9RPM/V Disc brake compatible: Yes Rim brake compatible: Yes Phase connectors: 3x M6 ring terminals Hall connectors: 2x 6-pin DJ7061Y-2.3-21/11 male Dropout width: 142mm Axle threads: M16x1.5 Motor type: Permanent magnet synchronous motor / brushless hub motor Number of magnet pole pairs: 23 Recommended freewheel: Single speed
449,00 €
Fardriver ND72340
48–72V, 120A battery current
This motor controller is powerful with a full 340A phase current, optimized for PMSM motors up to approx. 3 kW rated power when used in a recreational vehicle. It provides smooth, vibration-free operation thanks to sine wave drive and supports regenerative braking. Features: Sine wave, waterproof, regenerative braking, programmable, compatible with Hall sensors. NOTE programming cable sold separately. #SPECS Max power: 8640W Rated power: 1000-3000W Voltage range: 72V Phase current, max: 340A Battery current, max: 120A Regenerative braking: Yes Phase wire connector: M6 Battery cable connector: M6 Hall connectors: Yes Control modes: Forward, reverse, 3-speed, boost, brake low/high Protection: Locked rotor, overcurrent, overload, overtemperature, overvoltage, undervoltage Dimensions without cables: 179mm*117mm*61mm
229,00 €
Full twist throttle with voltmeter and ignition
12–99V, with key
This full twist throttle is compatible with e-bikes and scooters at 12–99V, with automatic voltage detection up to 100V. The digital voltmeter provides a real-time display of battery status, while the built-in key and three-speed switch add extra functionality. Mounts on standard 22.2 mm handlebars. Delivered complete with left and right grips and a 180cm cable. #SPECS Color: Bronze/gold Usable voltage: 12–99V Number of wires: 5 Type: Full twist, with voltmeter and ignition key Inner diameter: 22,2 mm Features: Battery voltage display, "ignition" Cable length: 180cm
17,90 €
Thumb throttle with soft spring
Hall effect sensor, universal compatibility
A quality thumb throttle with soft spring response that provides precise control and comfort. It uses a hall effect sensor and is compatible with all Gbike motors and controllers, making it a safe choice for all types of builds and upgrades. Fits common 22.2mm grips. #SPECS Type: Thumb throttle Sensor: Hall effect Compatibility: All Gbike controllers Spring: Soft Connector: JST SM 3-pin female Inner diameter: 22,2mm Cable length: 180cm
17,90 €
Ignition lock with voltmeter
12–99 V, two keys, black
Robust ignition lock with an integrated voltmeter that clearly shows the current battery voltage between 12 and 99 V. Comes with two keys and fits most electric vehicle builds. Black housing for discreet installation in the cockpit or panel. Fits standard bike handlebars with a diameter of 22,2mm. #SPECS Type: Ignition lock with voltmeter Voltage range: 12–99 V Color: Black Number of keys: 2 Diameter: 22,2mm Cable length: 180cm Connector: JST SM 3-pin male
Three-mode speed selector
Handlebar mount, modes I–III, black
A simple and smooth three-mode button for switching between different power or speed modes. Mounts directly on the handlebar and is compatible with most motor controllers that support multiple riding modes. A black universal model that fits practically all builds with a standard 22.2mm handlebar. #SPECS Type: Three-mode button Modes: I, II, III Mounting: On handlebar Color: Black Compatibility: Universal Inner diameter: 22.2mm Cable length: 160cm
17,90 €
8,90 €